[Solved] Ecoo e04 Aurora - OVERHEATING

[Cleopatra]

Because of my insomnia I am dedicated to the BIG problem that haunts all owners dell'Ecoo e04 Aurora: the OVERHEATING !
I think I found the ultimate solution (at least that's what they say on the site of the "developers"). Unfortunately, this solution requires to lower the frequency of the CPU (which is in itself absurd) ... but it seems to be the ONLY option if you want to avoid using the back of our Ecoo e04 to cook steaks.
You have to install 2 apps :
1) Uni-init + v1.0.apk
2) 3ctoolbox.free (although I recommend the Pro version ... since the free did not want to perform its duty on my Ecoo).

Tap on Uni-init + v1.0 ... tap on "Activate" and then tap on "Verify" (you should see the message "init.d supported")
Tap on 3ctoolbox (NOT check this box absolutely between modules Xposed) ... tap on the menu at the top left ... tap on "Managing CPU" ... lower the first frequency to 1.17GHz (I know ... it is absurd to buy a smartphone with 1.7GHz and then having to turn down it to 1.17GHz) ... tap on "Governor" and set on "powersave" ... tap on the white circle at the top right (you will see the message "settings saved in init.d ") ... and finally reboot your device. The following screenshots show to you the actual lowering of the CPU frequency (and unfortunately the poor score of Antutu):

[Cleopatra]

FUNDAMENTAL UPDATE :

I believe I have struck a fair balance between performances and overheating. On "3C Toolbox" don't set the parameters like I have suggested in the post above BUT use the settings shown in the following pic :



IMPORTANT : you have to set CPU max 1,41GHz and the Governors on "Interactive" (NOT check this box absolutely between modules Xposed). I have tested it on SpaceRom ... and finally no overheating issue in telephone conversation. Today I had a phone call of 14 minutes, and when I hang up (after 14 minutes), the temperature of my Ecoo was like the next pic :

[mnicolaas]

Hi cleopatra,
What do you mean with NOT check this box absolutely between modules Xposed? I've done the settings as per your updated instructions. Should I not activate the module and then reboot?

[Cleopatra]

Hi cleopatra,
What do you mean with NOT check this box absolutely between modules Xposed? I've done the settings as per your updated instructions. Should I not activate the module and then reboot?

Hi i' m in the train now. Exactly don' t check it and follow step by step my instructions in my last post. Have a nice week end :-)

[mnicolaas]

Hi cleopatra,
What do you mean with NOT check this box absolutely between modules Xposed? I've done the settings as per your updated instructions. Should I not activate the module and then reboot?

Hi i' m in the train now. Exactly don' t check it and follow step by step my instructions in my last post. Have a nice week end :-)

Ok I'll restart my phone later, it's charging now. And I won't activate the 3C Toolbox module in Xposed. Have to admit, that's quite counter-intuitive. Normally you tick the box and then reboot... I'll post some screenshots to confirm it's working.
Thanks and have a safe trip!

[Cleopatra]

Hi cleopatra,
What do you mean with NOT check this box absolutely between modules Xposed? I've done the settings as per your updated instructions. Should I not activate the module and then reboot?

Hi i' m in the train now. Exactly don' t check it and follow step by step my instructions in my last post. Have a nice week end :-)

Ok I'll restart my phone later, it's charging now. And I won't activate the 3C Toolbox module in Xposed. Have to admit, that's quite counter-intuitive. Normally you tick the box and then reboot... I'll post some screenshots to confirm it's working.
Thanks and have a safe trip!

Thanks :-)