MTK 6572 NOTE 3 HARD BRICKED

[1ikhan]

I lost my IMEI once too on my mtk6582.
All I had to do is flash the right firmware from [Only registered and activated users can see links Click here to register]. You can find it there probably.
Use SP Flashtools and make sure you have the correct VCOM drivers and ADB drivers.
VCOM: [Only registered and activated users can see links Click here to register]
ADB: [Only registered and activated users can see links Click here to register]

[mohammadyousef1]

Please help me as possible, I have a phone note 3 the same problem that you have a solution I want to beg

plz tell me what you do

[liveurdreamhigh]

Sir, I had bricked my samsung note 3 clone by flashing wrong preloader.
I got my mobile with locked network, so i tried to root ,and successfully rooted using MTK droid tool and then i installed CWM recovery, and maked backup of factory rom with CWM, afer that i write imei, and indian sim started working, but after reseting, i lost my samsung logo, so i was searching rom that i can flash.
when i used to turn on my mobile before bricking, on screen it show my model (samsung note 3 sm-n900), but on back side it is written GT-N9000, and also before bricking MTK droid tool detect my model as SM-n900 so i had flashed rom (sm-n900...) from needrom.com, but after successfully flashing by sp flashtool my mobile completely bricked, its not turing on (dead)
I had tried many rom, but getting same error ( ST_Enable DRAM failed (4032))

Please help me, i don't have sp flashable backup of my factory rom, and also i am not confirm about my hardware, once i have seen MTK droid tool detceted as MTK6572 device before bricking.
Is there any way that i can convert CWM recovery backup to sp flashable rom
HELP ME PLEASE

[PMoto]

I think your great problem is to know what hardware do you have for sure...!
Note 3 clones 6572 are not usual. Maybe 6589 or 6589T, 6582 or 6592.
Did you test it with AnTuTu? What were the results?
+/- 12000 -->6589
+/- 14500 -->6589T
+/- 17500 -->6582
+/- 24000 -->6592
or something very close to this...

After you know the processor you have, and knowing the real RAM and total memory, seach for a ROM for that values (CPU, RAM, Mem and screen size)

Them flash it.
The phone is detected by PC, so it's not dead... you just don't have the right ROM for it.
Remember, that's a clone, so that's dificult to know the right values, and get the right ROM.

TIP: If you have problems to flash, try to download only the Preloader first, unplug, restart FlashTools and them flash the hole ROM.

PMoto.

[liveurdreamhigh]

Hi PMoto, thanks for the help,

first time when i had benchmarking by antutu(which i got preinstalled) on my note 3 clone i got 3xxx( some three thousand ) result.
help me to know my hardware.

as i mentioned U earlier, can I convert my backup created by CWM recovery to sp flash tool rom, so that i can flash with flashtool. i have cwm recovery backup
help me....thanks.

[JOHNNYMAICON]

hello, I am Brazilian, I have a note n9006 clone 3, mtk6572, android 4.4
I did an update on sp flash tool, after completing my cell phone did not call, I think I installed the wrong rom, when I turn on the cpu does not load, does not go into recovery, just turn red sensor and nothing else .. help me please because my phone died, there is a solution? I have the backup of the original rom plus it's a sign of life

[martinmrnv]

HI!Did you find a solution of your problem!I have the same problem with same error massage!Cant flash my backup even!

[sayaranu]

HI!Did you find a solution of your problem!I have the same problem with same error massage!Cant flash my backup even!

hell yeah like mine
i have backup from my original ROM before flash to antoher ROM
but when i restore it's failed.can sum 1 tell me what's wrong?
thanks

[leo_hacker82]

imy phone is working now.... but i lost imei and no radio or baseband.. how can i flash it.. where can i find it...

Hi 'leo_hacker82' can you please elaborate how you unbrick your phone?
I face similar problem my phone now brick and every I flash with SP flash tool always end with BROM ERROR: S_FT_ENABLE DRAM FAIL (ERROR 4032).
I've many roms from need rom and other sites but always end with same Error Notofication. But unfortunately i have no backup

Can you or Somebody help me ?

My phone Specs
SAMSUNG GALAXY NOTE 3 CLONE
MODEL SM-N9006
FCC ID : A3LSMN9006
SSN:-N9006GSMH
PROCCESOR mtk 6572, RAM512, gpu mali 400, Screnn 5,7 inc

Any help will be appreciated

THE SOLUTION WAS...PRESS VOLUME DOWN..WHEN U HIT DOWNLOAD OR F9, PRESS VOL- OR VOL,+ IT WORKS FOR ME..AND THE FLASHING STARTS..
I HOPE IT WORKS

[naingwinhtet]

imy phone is working now.... but i lost imei and no radio or baseband.. how can i flash it.. where can i find it...

Hi 'leo_hacker82' can you please elaborate how you unbrick your phone?
I face similar problem my phone now brick and every I flash with SP flash tool always end with BROM ERROR: S_FT_ENABLE DRAM FAIL (ERROR 4032).
I've many roms from need rom and other sites but always end with same Error Notofication. But unfortunately i have no backup

Can you or Somebody help me ?

My phone Specs
SAMSUNG GALAXY NOTE 3 CLONE
MODEL SM-N9006
FCC ID : A3LSMN9006
SSN:-N9006GSMH
PROCCESOR mtk 6572, RAM512, gpu mali 400, Screnn 5,7 inc

Any help will be appreciated

Hello! poerwa
I have same problem with you. Are u solution for that? pls